BILT Speaker

BILT Speaker
RevitCat - Revit Consultant

Thursday 26 December 2013

Winder Stairs in Revit 2013

Revit Stair By Component


Revit 2013 introduced the concept of stairs by component.  Two of the new stair run component types were for creating "Winder Stairs".  

Winder Stairs

 
When I first tested these new tools I really struggled to get them to work at all, let alone well. I suspect that many people have since tried and failed to use them successfully. Here are a few tips that might help:
  • It is recommended that you only attempt to work with winder stair components if you have plenty of time and patience!
  • It may be more efficient to start a stair as a winder component but convert it to sketch as soon as it starts wasting your time.
Depending on which country you are working in, two different winder styles may work for you:
  • in Continental Europe it is common to use "balanced winders";
  • In Australia they are not suitable, so you need to use "single-point winders".
In Revit it is relatively easy to create a stair with 5 winders; but it is extremely difficult to adjust it down to only 3 to create a legal winder stair for use in Australia ( the maximum in the BCA) - it takes a lot of fiddling around with dimensions.

L-Shaped Winders


This requires just one mouse-click to place the start of the run, in the orientation shown in the tool icon.   
  • You can mirror the run before placing it, by ticking the “Mirror Preview” box on the options toolbar ;   
  • You can also rotate the stair by pressing the spacebar before placing it.  
  • It places the run with the number of risers you have set, depending on the full remaining stair height required; alternatively you can override the number of risers in the overall stair instance properties before you place it, then set the number back to the full number afterwards.   
  • There are two styles of winder stair available – “Balanced” or “Single-Point”
Balanced Winder Stair
Single-Point Winder Stair
  • Balanced winder stairs generally have angled risers spread over most of the stair – the change in angle of each riser is incremental.  These are commonly used only in continental Europe.
  • Single Point winders generally have parallel risers for most of the stair, while the angled risers are concentrated around the change in direction, with only a few winders.  These are more commonly used in the rest of the world, outside Europe.  This implementation of single-point winders has many limitations, and is very difficult to work with – it is impossible to create a stair with only 2 winder treads;  it is difficult to achieve only 3 or 4 winders.  The main reason for this is that the number of angled risers is controlled by setting the number of parallel treads.
 

  • This system works ok for balanced stairs, but for single-point stairs you actually want to define how many winders there are, but you are forced to do the reverse and calculate how many parallel ones you need in order to achieve it.

To place a single-point winder:

  • First set the desired height and run width properties;
  • Place a winder run, accepting the default layout;
  • Change the overall run lengths using the arrow shape handles;
  • Change its properties to a single-point winder;
  • Increase the number of parallel treads for each leg, but do it incrementally so that you can tell at which number it fails;
  • Fine tune the overall run lengths – place reference planes so that the shape handle arrows can snap to them (the only way to control it - important step).
 


  • It is almost impossible to control the location of the setout point for the winders – it seems that it has to be outside the run, not on the edge of the run as is normal in Australia.  The closest it will go is 26.35mm from the inside corner (in each direction), or 0.8mm in one direction, and 51.7mm the other. 
  • NB. when placing a winder stair, if you have just ticked the Mirror Preview  box, you may need to get the focus back on the main canvas before pressing the spacebar (use the middle mouse button to do it).

 U-Shaped Winder


These work in a similar fashion to L-shape winders.   If you use a balanced winder, Revit will balance the entire stair layout around the three legs of the run - this may work for you?


Single Point U-shaped winder stairs do not have any way to control the number of parallel treads in the middle section of the stair – thus rendering it completely useless unless you only require one parallel tread!
 
There is a rather dodgy workaround for U-Shaped Winder Stairs although the railings never really work properly

 

Modifying L-Shaped Winder Stairs


Single-point winder stairs are very difficult to work with and modify in Revit - so you may need help!  Balanced Winders are not discussed here as modification is somewhat simpler.


Once you have created a Single-Point winder stair, most likely you will have set the number of parallel treads on each leg to as high as Revit will let you (to keep the number of winder treads down to just 3).
 



Almost any subsequent change that you try to make to the winder run will result in an error message saying that it cannot be done. 
For example, if you try to adjust the number of treads on each leg of the winder by dragging an arrow shape handle at the top of the run, you will get an error message:
 


Most likely this is because it cannot deal with the adjusted number of parallel treads – it is trying to add a riser to the top, and remove one from the bottom of the run;  but the number of parallel treads at the start is set in the properties so it just fits into the run before the winders start.  When you try to change the run, it can no longer fit that number of parallel treads before the winders start. 
Solution:
The solution to this is to reset the number of parallel treads back to 1 or 2; 
 
Then make the change to the run (by dragging the top shape-handlle arrow for example - this will shorten the lower part of the run, and reduce the number of parallel treads again)
 
After that you need to reset the number of parallel treads to what will fit – it may not be the same as before, so you may need to recalculate how many are required.
 

This technique will probably be required for almost any change that you need to make to a single-point winder stair, including changes to stair width, height or dragging any shape-handles.

Shape-handles
The arrow shape-handles at the top and bottom of a winder stair behave like other stairs.  However,  it seems different because a winder stair does not usually have landings.  On a stair with a landing, dragging the arrow handles will move the stair ends by increments of one tread;  on a stair with no landings the shape handles allow free movement (no increment snapping) - hence the need for reference planes to snap to.

The square shape-handle in the middle of a winder will adjust the location of the selected leg of the winder - it moves the leg sideways, and as a result will adjust the length and end point of that leg while the other leg does not move (its end point stays fixed).  If you have a single-point winder, you will almost certainly get an error message if you try to drag it (refer to solution above).

Temporary Dimensions
Winder run lengths cannot be changed using the temporary dimensions - therefore it is wise to create reference planes so that you can snap to them when dragging shape handles.